 |
| Quantity: | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| JUTAI is a strategic partner of Victrex, supplying extrusion profiles including PEEK 450G, PEEK 450CA30, PEEK 450GL30, PEEK 450FC30, PEEK 450FE20, and CT200. | |||||||||
Semi-crystalline polyetheretherketone (PEEK) in pellet form for injection molding and extrusion
Standard flow grade with natural/beige coloration
Exceptional mechanical strength, stiffness, and thermal stability (continuous use up to 260°C)
Outstanding chemical resistance to hydrocarbons, acids, and steam
FDA-compliant for food contact applications
Excellent radiation resistance and biocompatibility (ISO 10993 certified)
Typical applications: Medical implants, semiconductor components, aerospace fittings
Enhanced tensile strength (210 MPa) and flexural modulus (15 GPa)
Superior wear resistance and dimensional stability
Reduced coefficient of thermal expansion (CTE) for precision parts
Electrically conductive (106-108 ohm-cm volume resistivity)
Common uses: Oil/gas drill components, robotic bearings, UAV structural parts
Balanced mechanical properties with 170 MPa tensile strength
Improved creep resistance under long-term loading
Excellent dielectric strength (20 kV/mm)
Lower thermal conductivity than carbon-filled grades
Typical applications: Electrical insulators, pump housings, automotive sensors
Ultra-low friction coefficient (dynamic μ 0.10-0.15)
Exceptional PV limit (3.5 MPa·m/s dry running)
Reduced wear rate (<1×10-6 mm³/N·m)
Maintains mechanical properties at high sliding speeds
Ideal for: Compressor vanes, thrust washers, non-lubricated bearings
Optimized for dry-running applications
50% lower wear rate compared to unfilled PEEK
Good chemical resistance except to strong oxidizers
FDA compliant version available
Common uses: Seal rings, guide rails, pharmaceutical equipment
Maintains ductility down to liquid nitrogen temperatures
No brittle fracture at cryogenic conditions
Low outgassing properties (TML<1%)
Space-grade purity with metal ion control
Applications: Superconductor components, LNG valves, space probe mechanisms
Semi-crystalline polyetheretherketone (PEEK) in pellet form for injection molding and extrusion
Standard flow grade with natural/beige coloration
Exceptional mechanical strength, stiffness, and thermal stability (continuous use up to 260°C)
Outstanding chemical resistance to hydrocarbons, acids, and steam
FDA-compliant for food contact applications
Excellent radiation resistance and biocompatibility (ISO 10993 certified)
Typical applications: Medical implants, semiconductor components, aerospace fittings
Enhanced tensile strength (210 MPa) and flexural modulus (15 GPa)
Superior wear resistance and dimensional stability
Reduced coefficient of thermal expansion (CTE) for precision parts
Electrically conductive (106-108 ohm-cm volume resistivity)
Common uses: Oil/gas drill components, robotic bearings, UAV structural parts
Balanced mechanical properties with 170 MPa tensile strength
Improved creep resistance under long-term loading
Excellent dielectric strength (20 kV/mm)
Lower thermal conductivity than carbon-filled grades
Typical applications: Electrical insulators, pump housings, automotive sensors
Ultra-low friction coefficient (dynamic μ 0.10-0.15)
Exceptional PV limit (3.5 MPa·m/s dry running)
Reduced wear rate (<1×10-6 mm³/N·m)
Maintains mechanical properties at high sliding speeds
Ideal for: Compressor vanes, thrust washers, non-lubricated bearings
Optimized for dry-running applications
50% lower wear rate compared to unfilled PEEK
Good chemical resistance except to strong oxidizers
FDA compliant version available
Common uses: Seal rings, guide rails, pharmaceutical equipment
Maintains ductility down to liquid nitrogen temperatures
No brittle fracture at cryogenic conditions
Low outgassing properties (TML<1%)
Space-grade purity with metal ion control
Applications: Superconductor components, LNG valves, space probe mechanisms
